View LD2982AM50R_37451.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LD2982 SERIES
VERY LOW DROP AND LOW NOISE VOLTAGE REGULATOR WITH INHIBIT FUNCTION, LOW ESR CAP. COMPATIBLE
s
s
s s
s
s s
s s s s s
VERY LOW DROPOUT VOLTAGE (120mV AT 50mA AND 7mV AT 1mA LOAD) VERY LOW QUIESCENT CURRENT (375A TYP. AT 50mA LOAD AND 75A AT 1mA) OUTPUT CURRENT UP TO 50mA LOGIC CONTROLLED ELECTRONIC SHUTDOWN OUTPUT VOLTAGE OF 1.5,1.8, 2.5, 2.8, 2.85, 3, 3.1, 3.2, 3.3, 3.5, 3.6, 3.8, 4, 4.7, 5V INTERNAL CURRENT AND THERMAL LIMIT AVAILABLE IN 1% TOLLERANCE (AT 25C, A VERSION) SUPPLY VOLTAGE REJECTION: 45dB (TYP) ONLY 1F FOR STABILITY LOW OUTPUT NOISE VOLTAGE 30Vrms SMALLEST PACKAGE SOT23-5L TEMPERATURE RANGE: -40C TO 125C
SOT23-5L
DESCRIPTION The LD2982 is a 50mA fixed output voltage regulator. The ultra low drop voltage and the low quiescent current make them particularly suitable for low noise, low power applications, and in battery powered systems. In sleep mode quiescent current is less than 1A when INHIBIT
pin is pulled low. Shutdown Logic Control Function is available on pin 3 (TTL compatible). This means that when the device is used as local regulator, it is possible to put a part of the board in standby, decreasing the total power consumption. An external capacitor CBYP=10nF connected between bypass pin and GND reduce the noise to 30Vrms. Typical application are in cellular phone, palmtop/ laptop computer, personal digital assistant (PDA), personal stereo, camcorder and camera.
SCHEMATIC DIAGRAM
July 2003
1/13
LD2982 SERIES
ABSOLUTE MAXIMUM RATINGS
Symbol VI VINH IO Ptot Tstg Top DC Input Voltage INHIBIT Input Voltage Output Current Power Dissipation Storage Temperature Range Operating Junction Temperature Range Parameter Value 16 16 Internally limited Internally limited -65 to +150 -40 to +125 C C Unit V V
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied.
THERMAL DATA
Symbol Rthj-case Parameter Thermal Resistance Junction-case SOT23-5L 81 Unit C/W
CONNECTION DIAGRAM (top view)
PIN DESCRIPTION
Pin N Symbol 1 2 3 Name and Function
4 SOT23-5L 5
IN Input Port GND Ground Pin INHIBIT Control switch ON/OFF. Inhibit is not internally pulled-up; it cannot be left floating. Disable the device when connected to GND or to a positive voltage less than 0.18V Bypass Bypass Pin: Capacitor to be connected to GND in order to improve the thermal noise performances. OUT Output Port
ORDERING CODES
A VERSION LD2982AM15R LD2982AM18R LD2982AM25R LD2982AM28R LD2982AM285R LD2982AM30R LD2982AM31R LD2982AM32R LD2982AM33R LD2982AM35R LD2982AM36R LD2982AM38R LD2982AM40R LD2982AM47R LD2982AM50R B VERSION LD2982BM15R LD2982BM18R LD2982BM25R LD2982BM28R LD2982BM285R LD2982BM30R LD2982BM31R LD2982BM32R LD2982BM33R LD2982BM35R LD2982BM36R LD2982BM38R LD2982BM40R LD2982BM47R LD2982BM50R OUTPUT VOLTAGES 1.5V 1.8V 2.5V 2.8V 2.85V 3.0V 3.1V 3.2V 3.3V 3.5V 3.6V 3.8V 4.0V 4.7V 5.0V
2/13
LD2982 SERIES
ELECTRICAL CHARACTERISTICS FOR LD2982A (TJ = 25C, VI=VO+1V, IO=1mA, VSHDN=2V, CI = 1F, CO = 1F, unless otherwise specified)
Symbol VOp VO Parameter Operating Input Voltage Output Voltage VI = 2.5V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 2.8V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 3.5V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 3.8V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 3.85V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 4.0V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 4.1V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 4.2V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 4.3V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 4.5V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 4.6V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 4.8V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 5.0V IO = 1 to 50mA IO = 1 to 50mA TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C Test Conditions Min. 2.5 1.485 1.477 1.470 1.782 1.773 1.764 2.475 2.462 2.45 2.772 2.758 2.744 2.821 2.807 2.793 2.970 2.955 2.94 3.069 3.053 3.038 3.168 3.152 3.136 3.267 3.250 3.234 3.465 3.447 3.43 3.564 3.546 3.528 3.762 3.743 3.724 3.96 3.94 3.92 4 3.8 3.6 3.5 3.3 3.2 3.1 3.0 2.85 2.8 2.5 1.8 1.5 Typ. Max. 16 1.515 1.523 1.530 1.818 1.827 1.836 2.525 2.537 2.55 2.828 2.842 2.856 2.879 2.893 2.907 3.030 3.045 3.06 3.131 3.146 3.162 3.232 3.248 3.264 3.333 3.349 3.366 3.535 3.552 3.57 3.636 3.654 3.672 3.838 3.857 3.876 4.04 4.06 4.08 Unit V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V
3/13
LD2982 SERIES
Symbol VO
Parameter Output Voltage VI = 5.7V
Test Conditions IO = 1 to 50mA IO = 1 to 50mA TJ= -40 to 125C
Min. 4.653 4.629 4.606 4.95 4.925
Typ. 4.7
Max. 4.747 4.77 4.794
Unit V V V V V V mA %/VI %/VI mV mV mV mV mV mV mV mV A A A A A A A A A A dB
VO
Output Voltage
VI = 6.0V IO = 1 to 50mA IO = 1 to 50mA TJ= -40 to 125C
5
5.05 5.075 5.1
4.9 150 0.003
ISC
Short Circuit Current
RL = 0 VI = VO+1V to 16V, IO = 1mA VI = VO+1V to 16V, IO = 1mA TJ= -40 to 125C
VO/VI Line Regulation
0.014 0.032
Vd
Dropout Voltage
IO = 0 IO = 0 IO = 1mA IO = 1mA IO = 10mA IO = 10mA IO = 50mA IO = 50mA TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C
1 7 40 120 80 TJ= -40 to 125C 100 TJ= -40 to 125C 200 TJ= -40 to 125C 600 TJ= -40 to 125C 0
3 5 10 15 60 90 150 225 100 150 150 200 300 400 900 1200 1
Id
Quiescent Current
IO = 0 IO = 0 IO = 1mA IO = 1mA IO = 10mA IO = 10mA IO = 50mA IO = 50mA OFF MODE VINH<0.18V OFF MODE VINH<0.18V TJ= -40 to 125C
SVR VIL VIH IiNH eN
Supply Voltage Rejection Control Input Logic Low Control Input Logic High Control Input Current
CBYP = 0.01F TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C
CO = 10F
f = 1KHz 2
45 0.15
V V A A V
VSHDN = 5V VSHDN = 0V
5 0 30
15 -1
Output Noise Voltage
B= 300Hz to 50KHz CO = 10F CBYP = 0.01F
4/13
LD2982 SERIES
ELECTRICAL CHARACTERISTICS FOR LD2982B (TJ = 25C, VI=VO+1V, IO=1mA, VSHDN=2V, CI = 1F, CO = 1F, unless otherwise specified)
Symbol VOp VO Parameter Operating Input Voltage Output Voltage VI = 2.5V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 2.8V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 3.5V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 3.8V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 3.85V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 4.0V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 4.1V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 4.2V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 4.3V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 4.5V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 4.6V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 4.8V IO = 1 to 50mA IO = 1 to 50mA VO Output Voltage VI = 5.0V IO = 1 to 50mA IO = 1 to 50mA TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C Test Conditions Min. 2.5 1.477 1.470 1.447 1.773 1.764 1.737 2.462 2.45 2.412 2.758 2.744 2.702 2.807 2.793 2.750 2.955 2.94 2.895 3.053 3.038 2.991 3.152 3.136 3.088 3.250 3.234 3.184 3.447 3.430 3.377 3.546 3.528 3.474 3.743 3.724 3.667 3.94 3.92 3.86 4 3.8 3.6 3.5 3.3 3.2 3.1 3.0 2.85 2.8 2.5 1.8 1.5 Typ. Max. 16 1.523 1.530 1.553 1.827 1.836 1.863 2.537 2.55 2.587 2.842 2.856 2.898 2.893 2.907 2.950 3.045 3.06 3.105 3.146 3.162 3.208 3.248 3.264 3.312 3.349 3.366 3.415 3.552 3.370 3.662 3.654 3.672 3.726 3.857 3.876 3.933 4.06 4.08 4.14 Unit V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V
5/13
LD2982 SERIES
Symbol VO
Parameter Output Voltage VI = 5.7V
Test Conditions IO = 1 to 50mA IO = 1 to 50mA TJ= -40 to 125C
Min. 4.629 4.606 4.535 4.925 4.9
Typ. 4.7
Max. 4.77 4.794 4.864
Unit V V V V V V mA %/VI %/VI mV mV mV mV mV mV mV mV A A A A A A A A A A dB
VO
Output Voltage
VI = 6.0V IO = 1 to 50mA IO = 1 to 50mA TJ= -40 to 125C
5
5.075 5.1 5.175
4.825 400 0.003
ISC
Short Circuit Current
RL = 0 VI = VO+1V to 16V, IO = 1mA VI = VO+1V to 16V, IO = 1mA TJ= -40 to 125C
VO/VI Line Regulation
0.014 0.032
Vd
Dropout Voltage
IO = 0 IO = 0 IO = 1mA IO = 1mA IO = 10mA IO = 10mA IO = 50mA IO = 50mA TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C
1 7 40 120 80 TJ= -40 to 125C 100 TJ= -40 to 125C 200 TJ= -40 to 125C 600 TJ= -40 to 125C 0
3 5 10 15 60 90 150 225 100 150 150 200 300 400 900 1200 1
Id
Quiescent Current
IO = 0 IO = 0 IO = 1mA IO = 1mA IO = 10mA IO = 10mA IO = 50mA IO = 50mA OFF MODE VINH<0.18V OFF MODE VINH<0.18V TJ= -40 to 125C
SVR VIL VIH IiNH eN
Supply Voltage Rejection Control Input Logic Low Control Input Logic High Control Input Current
CBYP = 0.01F TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C TJ= -40 to 125C
CO = 10F
f = 1KHz 2
45 0.15
V V A A V
VSHDN = 5V VSHDN = 0V
5 0 30
15 -1
Output Noise Voltage
B= 300Hz to 50KHz CO = 10F CBYP = 0.01F
6/13
LD2982 SERIES
TYPICAL CHARACTERISTICS (unless otherwise specified TJ = 25C, CI=1F, CO=2.2F, CBYP=100nF) Figure 1 : Output Voltage vs Temperature Figure 4 : Quiescent Current vs Load Current
Figure 2 : Dropout Voltage vs Temperature
Figure 5 : Quiescent Current vs Temperature
Figure 3 : Dropout Voltage vs Output Current
Figure 6 : Supply Voltage Rejection vs Temperature
7/13
LD2982 SERIES
Figure 7 : Supply Voltage Rejection vs Output Current Figure 10 : Supply Voltage Rejection vs Frequency
Figure 8 : Supply Voltage Rejection vs Output Current
Figure 11 : Line Transient
VO=2.5V, IO= 50mA, no CI, CO=4.7F, tr=tf=2ns
Figure 9 : Supply Voltage Rejection vs Frequency
Figure 12 : Line Transient
VO=2.5V, IO= 50mA, no CI, CO=4.7F, tr=tf=1s
8/13
LD2982 SERIES
Figure 13 : Load Transient Figure 14 : Load Transient
VO=2.5V, IO=0 to 50mA, no CI, CO=10F, ts=tf=2ns
VO=2.5V, IO=0 to 50mA, no CI, CO=4.7F, ts=tf=2ns
EXTERNAL CAPACITORS Like any low-dropout regulator, the LD2982 requires external capacitors for regulator stability. This capacitor must be selected to meet the requirements of minimum capacitance and equivalent series resistance. We suggest to solder input and output capacitors as close as possible to the relative pins. INPUT CAPACITOR An input capacitor whose value is 1F is required with the LD2982 (amount of capacitance can be increased without limit). This capacitor must be located a distance of not more than 0.5" from the input pin of the device and returned to a clean analog ground. Any good quality ceramic, tantalum or film capacitors can be used for this capacitor. OUTPUT CAPACITOR The LD2982 is designed specifically to work with ceramic output capacitors. It may also be possible to use Tantalum capacitors, but these are not as attractive for reasons of size and cost. By the way, the output capacitor must meet both the requirement for minimum amount of capacitance and E.S.R. (equivalent series resistance) value. Due to the different loop gain, the stability improves for higher output versions and so the suggested minimum output capacitor value, if low E.S.R. ceramic type is used, is 1F for output voltages equal or major than 3.8V, 2.2F for VO going from 1.8 to 3.3V, and 3.3F for the other versions. However, if an output capacitor lower than the suggested one is used, it's possible to make stable the regulator adding a resistor in series to the capacitor. IMPORTANT: The output capacitor must maintain its ESR in the stable region over the full operating temperature to assure stability. Also, capacitor tolerance and variation with temperature must be considered to assure the minimum amount of capacitance is provided at all times. This capacitor should be located not more than 0.5" from the output pin of the device and returned to a clean analog ground. INHIBIT INPUT OPERATION The inhibit pin can be used to turn OFF the regulator when pulled low, so drastically reducing the current consumption down to less than 1A. When the inhibit feature is not used, this pin must be tied to VI to keep the regulator output ON at all times. To assure proper operation, the signal source used to drive the inhibit pin must be able to swing above and below the specified thresholds listed in the electrical characteristics section under VIH VIL. Any slew rate can be used to drive the inhibit.
9/13
LD2982 SERIES
REVERSE CURRENT The power transistor used in the LD2982 has not an inherent diode connected between the regulator input and output. If the output is forced above the input, no current will flow from the output to the input across the series pass transistor. When a VREV voltage is applied on the output, the reverse current measured flows to the GND across the two feedback resistors. This current typical value is 160A. R1 and R2 resistors are implanted type; typical values are, respectively, 42.6 K and 51.150 K. Figure 15 : Reverse Current Test Circuit
10/13
LD2982 SERIES
SOT23-5L MECHANICAL DATA
mm. DIM. MIN. A A1 A2 b C D E e H L 2.60 0.10 0.90 0.00 0.90 0.35 0.09 2.80 1.50 0.95 3.00 0.60 102.3 3.9 TYP MAX. 1.45 0.10 1.30 0.50 0.20 3.00 1.75 MIN. 35.4 0.0 35.4 13.7 3.5 110.2 59.0 37.4 118.1 23.6 TYP. MAX. 57.1 3.9 51.2 19.7 7.8 118.1 68.8 mils
.
7049676C
11/13
LD2982 SERIES
Tape & Reel SOT23-xL MECHANICAL DATA
mm. DIM. MIN. A C D N T Ao Bo Ko Po P 3.13 3.07 1.27 3.9 3.9 3.23 3.17 1.37 4.0 4.0 12.8 20.2 60 14.4 3.33 3.27 1.47 4.1 4.1 0.123 0.120 0.050 0.153 0.153 0.127 0.124 0.054 0.157 0.157 13.0 TYP MAX. 180 13.2 0.504 0.795 2.362 0.567 0.131 0.128 0.0.58 0.161 0.161 0.512 MIN. TYP. MAX. 7.086 0.519 inch
12/13
LD2982 SERIES
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. (c) The ST logo is a registered trademark of STMicroelectronics (c) 2003 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. (c) http://www.st.com
13/13

▲Up To Search▲

Price & Availability of LD2982AM50R

	To Download LD2982AM50R Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .